Skip to main content

Components of Quad-copter Drone

 


  • Frame: There are two possibilities when it comes to a frame for your drone. You can make it yourself or buy it in an online store, and for a wide choice of high-quality frames, we suggest checking out our article about the best drone frames. If you decide to build it yourself, the project is not that difficult, but you’ll need some engineering knowledge and knowledge of the materials you are going to use. For instance, you can use metal (something light), plastic, or even wood slats. If you opt for a wooden frame, you’ll need a wood board that is about 2.5 cm thick.

 

  • Motors: For an ordinary quad, you will need 4 motors in total, but an octocopter requires eight motors to fly. The recommendation is to use brushless motors – they are lighter on the battery and, unless you are an engineer who completely understands how a motor works, these pieces should be bought from a store.

 

  • ESCs or electronic speed control: These are also essential pieces of your drone as they are in charge of delivering power to the motors. Again, their number depends on the number of arms your drone is going to have.

 

  • Propellers: When looking for the propellers, you must find the ones that match the frame of your drone. Pay attention to materials – you won’t find wooden propellers, but you must make sure the ones you choose are a good fit.

 

  • Connectors: You will need 3.5 mm connectors to weld the motors and ESCs, as well as 4.5 mm connectors for the power distribution board.

 

 

  • Batteries: When purchasing the batteries for your drone, you need to consider the capacity of a battery and its type. The most used batteries for this purpose are Li-Po batteries and their power differs. To have a much better insight on this topic.

 

  • Battery Monitor: This is not an elementary item, but the monitor is quite useful in warning you when the batteries are close to finishing. This way you don’t risk having the drone remain out of juice in the air, over a pond. A battery monitor ensures that your aerial vehicle won’t die in the most inopportune place.

 

  • Mounting pad: It reduces the vibrations, and thus improves the flight. This one is very useful especially if you are trying to take pictures or videos with your DIY drone.

 

  • ControllerThis device shares the power and commands the motors at the same time.

 

  • RC receiver: Of course, if you have a transmitter (which is usually with you), you’ll also have a receiver mounted on the drone.

 

  • Camera: If you want to take aerial photos and record the surroundings while flying your drone, you will need a camera. The best cameras are those that can take the quality 4K videos, but everyone will find one according to their needs. For high-quality aerial photography and videography, you might also need a gimbal for the camera.

 

 Source of Article Click HERE

 


Comments

Popular posts from this blog

Introduction of Quad-copter Drone

 A quadcopter is also called a quadrotor helicopter or quadrotor. The quadcopters are classified as rotorcraft, as opposed to fixed-wing aircraft because their life is generated by a set of the rotor. Quadcopters generally use two pairs of identical fixed pitched propellers; two clockwise (CW) and two counterclockwise (CCW). These use independent variation of the speed of each rotor to achieve control. By changing the speed of each rotor it is possible to specifically generate a desired total thrust; locate for the center of thrust both laterally and longitudinally, and to create a desired total torque, or turning force. Fig.1 Quadcopter Drone   Quadcopters differ from conventional helicopters, which use rotors that can vary the pitch of their blades dynamically as they move around the rotor hub. In the early days of flight, quadcopters (then referred to either as 'quad rotors' or simply as 'helicopters') were seen as possible solutions to some of the persistent problem...

Detail of Design, working and processes of Quad copter Drone

  STEP-BY-STEP INSTRUCTIONS There are different types of drones , but people find quadcopters to be more efficient, as they are easy to fly. So for this step-by-step guide, we have focused on showing you how to build a quadcopter with pieces that you can buy separately: STEP 1: MAKING THE FRAME No matter what your drone is going to be, it must have a frame. So, the first task is to make a frame. For this purpose, you can use different materials , such as metal, plastic, or wood. These materials will differ based on how sturdy you intend the drone to be. If you select wood for the frame, find a wood board that is longer than 60 cm and about 25-30 mm thick. Cut up this board in such a way as to get two laths which are 60cm long and 30mm wide. These two lengths are required to make the structure of your future quad. Fig. Materials of Quad Copter Drone   Crossing these two laths you’ll make the X frame. Also, you will need a wooden sheet to make and add a rectangular piece in...